The Conoflow GH22 Series Relay is used to boost, amplify or reduce the pneumatic signal of a controller or similar instrument in a predetermined ratio. Using an independent supply pressure for greater flow volume, the unit relays an instrument signal to a final control element such as a valve actuator.
-
The Conoflow Series GH30 Back Pressure Regulator is used to maintain a constant upstream pressure of gas, vapor or liquid. Designed for accurate regulation under low flow conditions, these units are widely used for protection of analysis instrumentation or as a relief valve in supply pressure lines to control devices.
-
Conoflow's Service (GH40 Series) Regulators are for applications where positive shut-off and minimum air consumption are required. These rugged units with flow capacities and performance characteristics which allow the units to operate in both instrument and industrial applications. Teflon Buna "N" Teflon diaphragms are standard in the Stainless Steel units.
-
Conoflow's Service (GH40 Series) Regulators are for applications where positive shut-off and minimum air consumption are required. These rugged units with flow capacities and performance characteristics which allow the units to operate in both instrument and industrial applications. Teflon Buna "N" Teflon diaphragms are standard in the Stainless Steel units.
-
Conoflow's Service (GH40 Series) Regulators are for applications where positive shut-off and minimum air consumption are required. These rugged units with flow capacities and performance characteristics which allow the units to operate in both instrument and industrial applications. Buna "N" diaphragms are standard in the aluminum units.
-
Conoflow's Service (GH40 Series) Regulators are for applications where positive shut-off and minimum air consumption are required. These rugged units with flow capacities and performance characteristics which allow the units to operate in both instrument and industrial applications. Buna "N" diaphragms are standard in the Brass units.
-
Conoflow’s Electro-pneumatic Transducers accept a variety of electrical input signals and convert them to proportional output signals of 3-15, 3-27 or 6-30 PSIG (21-103, 21-186 or 41-207 kPa).The GT_8 Series Transducers incorporate low impedance circuitry and a range selector jumper switch which can be positioned to accept 4-20 or 10-50 mA DC current inputs. The selector feature permits stocking only one unit that can be used in various locations throughout the plant. For easy field adjustment these units are equipped with an external zero setting and a built-in potentiometer on the circuit board for span adjustment.Optional input signal of 0-20 mA is available on the GT_8 Series.
Specifications:
- Input Range: 4-20 mA DC | 10-50 mA DC
- Nominal Input Impedance: 145 ohms | 60 ohms
- Linearity: ± 1%
- Temperature Effect: 0.2%FS/10°F (-12°C) change for a 2°F/minute rate of change (2)
- Ambient Temperature Range: 0° to +150°F (-18° to +66°C)
- Approx. Shipping Weight: 7 lbs. (0.77 Kg)
-
Conoflow's GT_8 Series Transducers are explosionproof approved by Factory Mutual (FM), Canadian Standards Association (CSA) and CENELEC. These units incorporate the same high-quality standards as our other I/P Transducer lines and are backed by Conoflow's years of experience as a leading manufacturer of instrumentation.These units accept a variety of electrical input signals and convert them to proportional output signals of 3-15, 3-27 or 6-30 PSIG (21-103, 21-186 or 41-207 kPa). Other output signals are also available. Consult the factory for details.
Specifications:
- Input Range: 4-20 mA DC | 10-50 mA DC
- Nominal Input Impedance: 145 ohms | 60 ohms
- Linearity: ± 1%
- Temperature Effect: 0.2%FS/10°F (-12°C) for a 30°F (-1°C) change in 15 minutes
- Ambient Temperature Range: 0° to +140°F (-18° to +60°C)
- Approx. Shipping Weight: 13 lbs. (5.9 Kg)