When wires can’t be run for practical or economic reasons, the WNM Wireless Network Module provides accurate and reliable point-to-point wireless connectivity between remote fi eld sites. The WNM is a bi-directional, spread spectrum radio modem that delivers the fl exibility and cost-saving advantages of wireless data transmission. It is ideal for use with Moore Industries’ NET Concentrator System® (NCS), as well as other SCADA and distributed I/O systems. Moore Industries is a world leader in the design and manufacture of interface instruments for industrial process control, system integration, and factory automation. Providing products and services to fortune 500 companies worldwide, the products of Moore Industries are used in industries such as: chemical and petrochemical; power generation and transmission; petroleum extraction, refining and transport; pulp and paper; food and beverage; mining and metal refining; pharmaceuticals and biotechnology; industrial machinery and equipment; water and wastewater; and environmental and pollution monitoring.
-
When wires can’t be run for practical or economic reasons, the WNM Wireless Network Module provides accurate and reliable point-to-point wireless connectivity between remote fi eld sites. The WNM is a bi-directional, spread spectrum radio modem that delivers the fl exibility and cost-saving advantages of wireless data transmission. It is ideal for use with Moore Industries’ NET Concentrator System® (NCS), as well as other SCADA and distributed I/O systems. -
The TRUNKSAFE Fault-Tolerant Fieldbus System provides a cost-effective, yet highly reliable, strategy to maintain continuous communications between field devices and a host system in the event of any single point failure (such as any open single wire) on a FOUNDATION fieldbus™ H1 or PROFIBUS PA segment. -
PC-Programmable Temperature
Transmitters–the TRY (isolated) and TRX
(non-isolated)–combine smart digital technology
with advanced analog operation to deliver superior
reliability, accuracy and ease of use. -
The TRUNKGUARD TPS400 Power Supply enables fast and easy implementation of fi eldbus systems by providing properly conditioned power for simplex and duplex FOUNDATION fi eldbus H1 networks. TRUNKGUARD TPS400 is FOUNDATION fi eldbus registered and fully compliant with FF831-1 (the technical specifi cation for fi eldbus power supplies). -
Dual Input Smart HART® Temperature Transmitters configure quickly and
easily to accept a direct signal input from a wide array of sensors and analog devices: -
the WORM Universal Flexible Temperature Sensor Installs Without Removing Temperature Transmitter Enclosure or Thermowell Components: -
The 330 is a process monitor with universal input that is multi-functional and microprocessor based. The 330 can function as a panel meter and trip (alarm), or as a panel meter with two trips (alarms), analog transmitter and digital transmission with the addition of the RS 485 serial communications option. -
Device Couplers provide easy and practical mechanisms for implementing fieldbus systems. TRUNKGUARD Series 300 Device Couplers (TG300) simplify the use of fieldbus devices in Zone 1 by allowing “live” access for maintenance and eliminating the need for Exd junction boxes. The TG300 Series offers our patented Automatic Segment Termination feature and a key-operated magnetic interlock which permits one spur at a time to be de-energized and worked on without shutting down the entire segment. -
Designed for General Purpose ,Non-Incendive and Zone 2 applications, TRUNKGUARD Series 200 Device Couplers (TG200) enable fast and easy implementation of fieldbus systems by connecting multiple devices to a main fieldbus trunk in FOUNDATION fieldbus™ H1 and PROFIBUS PA networks. TG200 Device Couplers are available in models that handle four to 20 fieldbus devices. -
The TFZ Programmable FOUNDATION Fieldbus
Temperature Transmitter saves wire and installation
costs by allowing up to 32 field devices to be
networked onto one, low cost FOUNDATION
fieldbus H1 segment. -
Universal TDY PC-Programmable
Temperature Transmitter features a large integral
display that shows real-time process status and valuable
loop diagnostic information. Combining smart
digital technology with advanced analog operation,
the TDY delivers superior reliability, accuracy and
ease of use. -
The TCS Temperature Concentrator System
substantially reduces the cost of transmitting
multiple temperature sensor measurements in
general purpose and hazardous area applications by
“concentrating” up to 32 signals onto one network. -
The SIL 2 and SIL 3 capable STZ Functional Safety Dual Input Smart HART® Temperature Transmitters for your SIS (Safety Instrumented System) confi gures quickly and easily to accept a single or dual input from a wide array of sensors and analog devices:- 14 RTD Types
- 9 Thermocouple Types
- Resistance and Potentiometer Devices
- Direct Millivolt Sources
Features:
- STZ-DIN Functional Safety Dual Input Smart HART® Temperature Transmitter now includes associated Intrinsically-Safe Sensor Connections. The intrinsically–safe –AIS option allows direct connection of sensors located in Non-Hazardous or Class 1, Division 2/Zone 2 hazardous locations with sensor input terminals connected to equipment or sensors located in Class I , II III, Division 1 /Zone 0/1 hazardous locations since it includes an internal intrinsically-safe barrier in the front end of the THZ3.
- exida certifi ed to IEC 61508:2010. Certified by exida to IEC 61508 for systematic integrity up to SIL 3 and for random integrity up to SIL 2. This means that an STZ is approved for single use in Safety Instrumented Systems (SIS) up to SIL 2 and in a redundant architecture (1oo2, 2oo3, etc.) up to SIL 3.
- Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA data is available for a functional safety practitioner to use in determining the STZ applicability in specific safety-related applications.
- Dual sensor input for Backup and Failover Protection, Average and Differential measurement and Low or High Select.
- Device Intelligence including Sensor Drift and Corrosion Detection, Smart Range Alarms, High-availability option, and Input Simulation capability.
- HART 7 compliant with exception-based reporting and dynamic variable mapping.
- HART Access Control. To prevent unauthorized or accidental reconfiguration of the STZ while it's performing it's safety function, it has an added security feature to allow users to set HART communication into a Read Only or Off mode.
- Input-to-output analog accuracy of up to ±0.014°C (±0.025°F)* is the absolute best in the industry.
- 20-bit input resolution delivers exceptional digital accuracy of ±0.1°C (±0.18°F) with all Pt RTDs or up to ±0.05°C (±0.09°F)* for Pt1000 RTDs.
- HART & DTM Programmable with user-oriented basic configuration for fast and accurate setup. HART configurable via any HART handheld configurator or HART compatible host. Additionally program or monitor with any FDT compliant host or program, such as PACTware, utilizing our DTM.
- Long-term stability provides up to 5 years between scheduled calibrations.
-
STA SIL 2 and SIL 3 Compliant Programmable Current/Voltage and RTD/Thermocouple Safety Trip Alarms
The exida® SIL 2 and SIL 3 certified STA Safety Trip Alarm performs as a logic solver and acts on potentially hazardous process conditions; warns of unwanted process conditions; provides emergency shutdown; or provides on/off control in Safety Instrumented Systems (SIS) and traditional alarm trip applications. The 4-wire (line/mains-powered) STA models accept a signal input from transmitters, temperature sensors and a wide array of other monitoring and control instruments including:Current and Voltage Signals Temperature (RTD and T/C) Sensor Inputs Resistance and Potentiometer Devices Direct Millivolt Sources
Features:
- exida certified IEC 61508:2010. For systematic integrity up to SIL 3 and for random integrity up to SIL 2. This means that an STA is approved for single use in Safety Instrumented Systems (SIS) up to SIL 2 and in redundant architectures (1oo2, 2oo3, etc.) up to SIL 3.
- Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA (Failure Modes, Effects and Diagnostics Analysis) data is provided to be used by a competent functional safety practitioner to determine the STA’s applicability as a logic solver in specific safety-related applications.
- 20-bit input resolution with long-term stability. Delivers industry-best digital accuracy with up to 5 years between scheduled calibrations.
- Site-programmable with password protection. Front panel pushbuttons with menu-guided configuration deliver confident and secure set up.
- Large 5-digit process and status readout. Backlit display shows menu prompts during configuration and, when in operation, shows the process variable, the output or toggles between the two in selectable engineering units.
- Isolated and RFI/EMI protection. Delivers superior protection against the effects of ground loops and plant noise.
- Combined alarm trip and transmitter. The analog output (-AO) option reduces costs and installation time when both alarm and transmitter functions are needed at the same location.
-
SSX/SST Safety Series Isolator & Splitter
FS Functional Safety Series, the exida® approved, SIL 3 capable 2-wire (loop powered) SSX and 4-wire (line/mains powered) SST Safety Isolators and Splitters provide isolation and signal conversion for your SIS (Safety Instrumented System) needs. These units protect and enhance loops and also pass valuable HART® data from the field transmitter to host systems and vice-versa.Isolate your SIS from your Basic Process Control System or monitoring system so disconnections or failures to these secondary systems don’t affect your safety system. FMEDA (Failure Mode Effects and Diagnostic Analysis) reports are available with the required safety data to ensure that risk reduction requirements are met.Protect your safety system from surges, spikes and transients in the field. With 1500Vrms isolating capability, the SSX/SST protects your safety I/O cards and system from the rigors of plant environments.With built-in HART pass-through technology you can rest assured that when your loops use HART transmitters that critical and valuable HART diagnostic, process, and calibration information can be read on either side of the SSX/SST. Most all other isolators block and “strip off” the HART signal.Features:
- exida certified IEC 61508:2010. exida has certified the SSX/SST for use in an SIS up to SIL 3 in monitor mode, where only the input circuit is part of the safety function. For single use mode, the SSX/SST is approved for use in an SIS up to SIL 2.
- Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA data is provided to be used by a functional safety practitioner to determine the SST’s and SSX’s applicability in specific safety-related applications.
- Valuable HART data not lost. Both the SSX and SST pass critical HART data to asset management systems, programming devices or host systems.
- Split signals between two locations. The 4-Wire SST takes in one signal and gives you two fully isolated outputs that can be taken to two separate receiving devices. This facilitates maintenance on either output loop without losing the signal on the other output loop.
- RFI/EMI Protection. Standard 20V/m protection offered to protect against harmful effects of radio frequency and electromagnetic interference.
- Transmitter excitation. The 4-wire SST is capable of providing loop power to a 2-wire transmitter that is connected to its input.
-
SRM FS FUNCTIONAL SAFETY RELAY MODULE
SRM Safety Relay Module provides a high level of availability for safety-critical applications and as a part of Safety Instrumented Systems (SIS). It has been developed following the IEC 61508 standard and is certified by exida for single use in Safety Instrumented Systems up to SIL 2. The SRM is a relay repeater model that accepts a single contact closure input from a logic solver trip output such as the Moore Industries STA Safety Trip Alarm or the SPA2 Programmable Limit Alarm Trip. The SRM provides three contacts per alarm input, allowing you to add alarm contacts for your safety processes without special installation or configuration. Force Guided Relay Unlike traditional multi-output off-the-shelf interposing relays, the SRM is built using a safety-rated relay with forcibly-guided contacts. This design is commonly used in control and safety systems where the logic of an application needs to detect the state of the output contacts. This is achieved by monitoring the state of the monitor contact that is also mechanically linked to the same armature as the output contacts. A Force Guided Relay avoids the possibility of having contacts stuck in the Normally Open (NO) and Normally Closed (NC) states at the same time. Also known as a Positively Guided Relay, the Force Guided Relay assures users that mechanical problems such as welded contacts won’t be missed. Rugged Housing The SRM is housed in a DIN case that can be mounted on 35mm Top-Hat DIN-rail. The aluminum housing is more rugged and durable than safety relays housed in a plastic case.Features:
- exida certified to IEC 61508. exida has certified the SRM for single use in a Safety Instrumented System up to SIL 2.
- Comprehensive FMEDA certified safety data.Upon request, exida-certifi ed FMEDA (Failure Modes, Effects and Diagnostics Analysis) data is provided to be used by a competent functional safety practitioner to determine the SRM’s applicability in specific safety-related applications.
- Visual diagnostic information. Front-panel LEDs provide diagnostic information, with three LED indicator lights that show the Input, Output and Power status. The panels provide an instant visual diagnostic on the SRM, setting users quickly see if there are any potential problems.
- Easy to install and configure. The SRM can be installed in a Safety Instrumented System with minimal wiring. Simply provide a contact closure input to the SRM and you get three process relay outputs. A monitor relay is also provided.
- Input Snubber. The Contact Closure input circuit includes an internal snubbing diode across its relay coil, meaning there is no need for external suppression across the input terminals.
- Fuse protection. Input power and all four relay outputs on the SRM are fuse protected.
- RFI/EFI protection. Enhanced RF immunity up to 20V/m, 20-1000MHz when tested to IEC 61000-4-3.
-
The universal SPD Programmable Loop Display accepts a 4-20mA input from a process transmitter or similar analog device and indicates real-time process status in mA, percent or any designated engineering unit (EGU) on its 5-digit display. Both the process value and engineering unit (up to 5 characters) are shown on the display. -
The universal SPA2IS Programmable Limit Alarm Trips provide on/off control, warn of unwanted process conditions, alarm on rate-of-change and provide emergency shutdown. Very versatile, they accept signal inputs from transmitters and temperature sensors that are located in hazardous areas where the method of protection implemented by the plant or facility is Intrinsic Safety. -
The universal SPA2 Programmable Limit Alarm Trips provide on/off control, warn of unwanted process conditions, alarm on rate-of-change and provide emergency shutdown. Very versatile, they accept a signal input from transmitters, temperature sensors and a wide array of other monitoring and control instruments -
SLD Functional Safety Programmable Loop Display
Moore Industries’ universal SLD PC-Programmable Functional Safety Loop Display features a large integral display that shows real-time process status in mA, percent, or any designated 5-character Engineering units (EGU). The SLD is part of Moore Industries’ FS Functional Safety Series products. It is certified by exida as a SIL3 capable, non-interfering device for use in a safety loop. The SLD Functional Safety Programmable Loop Display is the perfect solution to accurately and reliably display process status in a safety loop:Features:
-
SIL3 Capability. The SLD is certifi ed by exida for non-interference in a safety loop. (It is not SIL3 assessed or certifi ed to be used as part of the safety function).
-
Easy-to-read, customizable display. The SLD’s independently confi gured display features two rows of large characters that can be clearly read in the fi eld and set to display any EGU.
-
360° fl exible mounting. When placed into one of our housings, the SLD can be mounted at any angle in nearly any environment.
-
Low voltage drop. Loop-powered by less than 2.3 Volts, the SLD can even be installed on burdened loops.
-
Loop Maintenance Zener Diode Option. Allows the SLD to be removed from the loop for maintenance without interrupting your safety function.
-
Custom and square root curves. Select a square root or linear curve from the library, or create your own. Use our software to input a table in one EGU and have the PC program convert it into a different EGU for display.
-
-
SIY PC-Programmable Signal
Isolator/Converter combines smart digital technology
with advanced analog operation to deliver superior
reliability, accuracy, and ease of use.
The highly versatile SIY programs to accept a wide
range of current or voltage inputs. It outputs an
isolated, proportional, 4-20mA signal. As a fl exible
analog/digital hybrid, this 2-wire (loop-powered)
transmitter programs in seconds to handle a wide
range of important signal interface applications. -
Functional Safety Frequency-to-DC Transmitter with Display
The SFY Functional Safety SIL 3 capable Frequency-to-DC Transmitter with Display is part of Moore Industries’ FS Functional Safety Series. It monitors frequency, period, high or low pulse width, and contact closure signals and converts the input signal to a proportional, input-to-output isolated 4-20mA output ready for direct interface with a Safety System, readout instrument, recorder, PLC, DCS, SCADA system. The 2-wire (loop-powered) SFY is ideal for use in your Safety Instrumented System (SIS) in a wide range of process and factory automation monitoring applications:Applications:
- Turbine Tachometer Generators
- Turbine Flow Meters
- Magnetic Pickups
- Dry Contact Closures
- Variable Frequency Drives
- Rotating Equipment
- Pulse and Frequency Output Transducers
- Motor and Conveyor Speed
Features:
- exida certified to IEC 61508:2010. Certified by exida to IEC 61508 for systematic integrity up to SIL 3 and for random integrity up to SIL 2. This means that an SFY is approved for single use in Safety Instrumented Systems (SIS) up to SIL 2 and in a redundant architecture (1oo2, 2oo3, etc.) up to SIL 3.
- Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA data is available for a functional safety practitioner to use in determining the SFY’s applicability in specific safety-related applications.
- Exceptional accuracy and long-term stability. Typical accuracy is ±0.025% of span with up to 5 years between scheduled calibrations.
- Sets up in minutes with PC software. You can choose, and then view to confirm, all application specific operating parameters.
- Versatile input choices. Measures frequency ranges between an amazingly low 0.005Hz up to 25kHz; periods from 40microseconds to 200sec; and pulse widths from 0.2msec to 200 seconds.
- Programmable moving average filter. Minimizes measurement instability caused by the effects of bent turbine blades and other frequency variations.
- User-configurable display. A 5-digit LCD shows the process variable in selectable engineering units.
- Input-to-output isolated and RFI/EMI protected. Resistant to unpredictable ground loops and the harmful effects of plant and equipment “noise”.
-
The versatile construction of the SB stainless steel enclosure makes it ideal for use with any manufacturer’s hockey-puck units. It protects all Moore Industries’ hockey-puck instruments. -
The UL Approved ECT-DIN 2-Wire Isolator is now available in a narrow 15mm aluminum housing. The thinner ECT-DIN 2-Wire Isolator with 15mm width retains the same General and Hazardous area approvals as the rest of the ECT family of isolators. It also has the same RFI/EMI protection and -40°C to 85°C operating temperature range. The ECT-DIN 2-Wire Isolator can be installed in hazardous locations and does not require installation in climate-controlled environments, making it perfect for more extreme locations.
The rugged narrow 15mm ECT DIN 2-Wire isolator and converter with 4-20mA, 1-5V and 0-10V inputs and 4-20mA output, permits more isolators to fit in cabinets and field enclosures where installation space is limited, saving space and money.” The ECT DIN 15mm narrow size allows more isolators to fit in cabinets and field enclosures where installation space is a premium. This is ideal for utilizing existing field mounted cabinets. The solid metal housing stands up to the continuous, daily rigors of process control and factory automation applications. An optional externally-mounted flange provides a secure mount, which ensures secure installation in high vibration environments. The ECT is UL approved Class I, Division 2, Groups A, B, C & D T4.
The rugged and reliable ECT family of isolators provides versatile choices to match the type of AC or DC power available at each location. ECT-DIN 2-wire Output-Loop powered models, ECT 2-wire Input-Loop powered models, or 4-wire (Line/Mains) Powered Isolators/Converters and Splitters are also available. The complete ECT family delivers reliable signal isolation and conversion solutions for the most demanding ambient and noisy installation conditions.
Download Data Sheet -
The ROUTE-MASTER™ RM100 Series is an intrinsically-safe fieldbus power supply system providing galvanically-isolated and fieldbusconditioned power for FOUNDATION Fieldbus or PROFIBUS PA segments. Fieldbus devices may be connected into these segments only through RMA100 or RMA100C Device Couplers, and any intrinsicallysafe segment may only contain intrinsically-safe devices, that are approved for the appropriate Zone/Division of use and the appropriate Gas hazard. -
The R-BOX accommodates transmitters, meters, indicators, analyzers, integrators, and many other rail-mounted instruments. The variety of available R-BOX sizes means that we have an R-BOX that will fi t your process needs. Choose from standard internal widths of 3, 6, 9, and 12 inches. Designed to meet Type 4X and IP66 ratings, the R-BOX is resistant to ultraviolet rays and chemicals. Its high-impact structure protects instruments even in harsh fi eld conditions. -
Moore Industries’ AC Power Transducers continuously track the amount of power being consumed by an electric device or a system. Available models accept an AC input from a “load” device such as a motor, pump or heater. They provide a proportional milliamp output for determining equipment power use and operating efficiency. They can also be used to trip automatic power control equipment to initiate energy conservation measures. Moore Industries’ AC power transducers are available in 1, 1-1/2, 2, 2-1/2, and 3 element versions. They may be either self- or externally-powered. -
Moore Industries’ universal PSD PC-Programmable Loop Display features a large integral display that shows real-time process status in mA, percent, or any designated 5-character Engineering units (EGU). Superior Accuracy–The loop-powered PSD reads any 4-20mA signal and displays the information with phenomenal accuracy of ±0.012% of input scale. And because it requires less than 2.3 Volts, it won’t burden most loops. Simple and Versatile PC Setup Program– Using the PC software, the PSD can either be custom scaled to display in a percent or scaled directly into engineering units for indicating process measurements such as pressure, temperature, level, or fl ow. Span, zero, input range, display range, and fi ltering frequency can also be easily programmed. Our software will even capture the input range limits of the loop to provide you with the most accurate display available -
Moore Industries’ family of pressure-to-current transmitters provide an economical solution when a pneumatic device must interface with a data acquisiton/control system, controller, recorder, or other electronic instrument. These compact, yet powerful units accept a pneumatic signal (3-15 psig, 0.2-1 bar, 3-27 psig, etc.) and accurately convert it to a proportional 4-20mA (or 10-50mA) output. Control Room and Field Mounting—Our complete line of P/I transmitters includes models perfect for both control room and field mounting. Moore Industries’ P/I transmitters are available with a wide variety of housings, and with special features and options. For detailed information, see Table 1 and the Ordering Specifications table. -
Moore Industries’ durable PIH Pressure–to-Current Transmitter provides an economical solution for any process that requires a rugged instrument capable of interfacing a pneumatic device with a data acquisition / control system, controller, recorder or other electronic instrument. This compact yet powerful unit accepts most pneumatic signals (3-15psig, 0.2-1 bar, 3-27 psig etc.) and accurately converts them to a proportional 4-20mA output. -
The universal CPT PC-Programmable Temperature
Transmitter and Signal Isolator/Converter accepts a
direct signal input from a wide array of sensors and
analog devices -
Moore Industries’ PAC and PAV Ac Current and Voltage Transducers accept an ac current (PAC) or ac voltage (PAV) input. They provide a highly accurate (±0.25% of rated output) dc current output. The PAC and PAV respond to the average value of the input signal and are calibrated to indicate the RMS value. -
Designed specifically for demanding industrial applications, the NET Concentrator System® (NCS) provides a real-time signal gateway between the field or factory floor and your control strategy. -
Featuring a very narrow installation footprint,
miniMOORE™ Signal Isolators, Converters, Boosters
and Splitters combine multiple analog signal channels
in a rugged, easy-to-install signal conditioner.
Reliable and very economical, the miniMOORE
multi-channel family includes the model MIX 2-wire
(loop) and the model MIT 4-wire (line/mains) powered
models. The complete family delivers cost-effective
solutions for an expansive range of signal interface
applications. -
The microNCS provides a real-time signal gateway between the field or factory floor and your control strategy. Part of Moore Industries’ NCS NET Concentrator System® family of intelligent distributed I/O, the stand-alone microNCS accepts four or eight fully-isolated analog inputs and four discrete (contact closure) inputs. It “concentrates” this data onto one or multiple communication links, and transmits it long distances back to one or more host DCS, PLC or PC-based control systems. -
Perfect for Head-Mount Instruments The LH connection heads are ideal for use with head-mount transmitters such as Moore Industries’ TRX/TRY PC-Programmable and THZ2 Smart HART® Temperature Transmitters. The LH heads also protect terminal blocks used for sensor wire terminations.