The K-system comprises signal conditioners for signal transfer between control system and safe area as well as isolated barriers for communication with field devices in hazardous areas. They are preferred for these kinds of mixed applications. Wide range of isolated barriers and signal conditioners for mixed applications
Modules for universal power supply
Reduced wiring by Power Rail
Removable terminals
Many modules with marine approvals and SIL assessment -
The K-system comprises signal conditioners for signal transfer between control system and safe area as well as isolated barriers for communication with field devices in hazardous areas. They are preferred for these kinds of mixed applications. Wide range of isolated barriers and signal conditioners for mixed applications
Modules for universal power supply
Reduced wiring by Power Rail
Removable terminals
Many modules with marine approvals and SIL assessment -
VisuNet industrial monitors and panel PCs are constructed for process control. Each and every industrial monitor is manufactured to meet rigid safety and mechanical tolerances.
Download Data Sheet -
Glass fiber reinforced polyester (GRP) enclosure, Ex e and Ex tb certified, 110 mm x 110 mm x 65 mm, Customizable configuration of cable gland types as per specification, Installation in Zone 1, Zone 2, Zone 21 and Zone 22 -
Limit value switches signal whether the medium being monitored has reached, risen above, or fallen below, a set level (VDI/VDE Directive 3519) based on its installation height.
Examples:
Overflow / dry-run protection
Minimum-maximum control
Overspill protection -
By combining low-cost wireless sensing with high-speed automated analytics, iTracking® Systems provide Cities, Utilities and Consulting Engineering firms with all the necessary tools for:
Inflow & Infiltration Micro Detection
Early-Warning Overflow and Backup Prevention
Dynamic Condition Assessment
Fact-Based Model Validation -
SSX/SST Safety Series Isolator & Splitter
FS Functional Safety Series, the exida® approved, SIL 3 capable 2-wire (loop powered) SSX and 4-wire (line/mains powered) SST Safety Isolators and Splitters provide isolation and signal conversion for your SIS (Safety Instrumented System) needs. These units protect and enhance loops and also pass valuable HART® data from the field transmitter to host systems and vice-versa.Isolate your SIS from your Basic Process Control System or monitoring system so disconnections or failures to these secondary systems don’t affect your safety system. FMEDA (Failure Mode Effects and Diagnostic Analysis) reports are available with the required safety data to ensure that risk reduction requirements are met.Protect your safety system from surges, spikes and transients in the field. With 1500Vrms isolating capability, the SSX/SST protects your safety I/O cards and system from the rigors of plant environments.With built-in HART pass-through technology you can rest assured that when your loops use HART transmitters that critical and valuable HART diagnostic, process, and calibration information can be read on either side of the SSX/SST. Most all other isolators block and “strip off” the HART signal.Features:
- exida certified IEC 61508:2010. exida has certified the SSX/SST for use in an SIS up to SIL 3 in monitor mode, where only the input circuit is part of the safety function. For single use mode, the SSX/SST is approved for use in an SIS up to SIL 2.
- Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA data is provided to be used by a functional safety practitioner to determine the SST’s and SSX’s applicability in specific safety-related applications.
- Valuable HART data not lost. Both the SSX and SST pass critical HART data to asset management systems, programming devices or host systems.
- Split signals between two locations. The 4-Wire SST takes in one signal and gives you two fully isolated outputs that can be taken to two separate receiving devices. This facilitates maintenance on either output loop without losing the signal on the other output loop.
- RFI/EMI Protection. Standard 20V/m protection offered to protect against harmful effects of radio frequency and electromagnetic interference.
- Transmitter excitation. The 4-wire SST is capable of providing loop power to a 2-wire transmitter that is connected to its input.
-
Featuring a very narrow installation footprint,
miniMOORE™ Signal Isolators, Converters, Boosters
and Splitters combine multiple analog signal channels
in a rugged, easy-to-install signal conditioner.
Reliable and very economical, the miniMOORE
multi-channel family includes the model MIX 2-wire
(loop) and the model MIT 4-wire (line/mains) powered
models. The complete family delivers cost-effective
solutions for an expansive range of signal interface
applications. -
PC-Programmable Temperature
Transmitters–the TRY (isolated) and TRX
(non-isolated)–combine smart digital technology
with advanced analog operation to deliver superior
reliability, accuracy and ease of use. -
Description The HCS HART Concentrator System converts a HART digital signal to a serial (RS-485 or RS-232) MODBUS RTU communication protocol. This allows HART transmitters and valves to interface directly with MODBUS-based monitoring and control systems. -
The ROUTE-MASTER™ RM100 Series is an intrinsically-safe fieldbus power supply system providing galvanically-isolated and fieldbusconditioned power for FOUNDATION Fieldbus or PROFIBUS PA segments. Fieldbus devices may be connected into these segments only through RMA100 or RMA100C Device Couplers, and any intrinsicallysafe segment may only contain intrinsically-safe devices, that are approved for the appropriate Zone/Division of use and the appropriate Gas hazard. -
The microNCS provides a real-time signal gateway between the field or factory floor and your control strategy. Part of Moore Industries’ NCS NET Concentrator System® family of intelligent distributed I/O, the stand-alone microNCS accepts four or eight fully-isolated analog inputs and four discrete (contact closure) inputs. It “concentrates” this data onto one or multiple communication links, and transmits it long distances back to one or more host DCS, PLC or PC-based control systems. -
The high-performance IPT 2 Current-to-Pressure (I/P) Transmitter converts a current signal to a pneumatic signal so that an electronic-based system such as a DCS, PLC, or PC can control a pneumatic actuator, valve, or damper drive. Available models accept a wide range of current inputs (4-20mA, 4-12mA, and 12-20mA) and provide a proportional pneumatic signal (3-15psig, 0.2-1 Bar, 20-100kPA, etc.).