Shop - Page 13 of 16 - CB Automation Inc.

ProPulse Series All Plastic Mini Turbine Flowmeter

ProPulse Series All Plastic Mini Turbine Flow Meter

No Programming Required Excellent Chemical Resistance Perfect for Dosing / Pulsating Flows

Features:

Universal Body 5 Different Flow Ranges(Flow Jets Are Field Replaceable)
Excellent Chemical Resistance
All Plastic PVDF Body, Rotor, Sapphire Bearings
Ultra Low Flow Ranges from 50 ml/min (.013 GPM)
Pressure Rating 10 bar (150 psi)
Pulse Output Hall Effect Sensor which converts the rotation into a square wave NPN pulse output
Compact - Lightweight
Temperature Rating -40 -120°C (-40 -248°F)
Barbed Hose Inlet/Outlet Connection 5/16 and 1/2 inch. 8mm, 12mm, or 3/8” Pipe Connector
High Accuracy & Repeatability
NPN Frequency Pulse Output

Details

PROSCAN SERIES – PP, PTFE LEVEL RADAR TRANSMITTER

PROSCAN SERIES - PP, PTFE LEVEL RADAR TRANSMITTER

The ProScan Series transmitter measures the liquid level inside the tank or sump by using an all plastic (PP or PTFE) antenna or horn that sends and receives low energy radar pulses. The sensor is mounted to the top of the tank and the pulsed signal is reflected off the liquid surface, the echo (returned signal) is then picked up or received by the transmitters antenna. The time it takes is compared to known laws of physics (speed of light), once this is done the distance can be determined, and very accurately measured. Distance = (Speed of Light x Time Delay) / 2 The ProScan Series does not contact the process liquid and therefore is an excellent choice for applications that may be corrosive, coating, dirty, or crystallizing. The are temperature compensated over the entire range (-40260°F) and can be used on to measure liquid under pressure or vacuum. The ProScan Series is both reliable and accurate; there is no requirement for re-calibration, and virtually zero maintenance as there are no moving parts. The ProScan Series utilizes a special microprocessor technology and mapping software that allows it to be used where other non-contact level sensing products fail or go lost i.e. Ultrasonics on Foam, Vapor, Condensate or Turbulence.

Excellent Chemical Resistance High Accuracy Suitable for Foam / Vapor

Features:

All Plastic PTFE Teflon Design
Small Dead Band 12”
PP, PTFE Antenna (Horn)
Low Profile
Simple Programming
Suitable for Dense Foam, Vapor
Excellent Chemical Resistance
Fail Safe Diagnostics
Simple Configuration
Push Button
IP67 Housing
Epoxy Coated
Loop Powered/ 2 Wire
Visual Display Window

Details

PSD PC-Programmable 4-20mA Loop Display

Moore Industries’ universal PSD PC-Programmable Loop Display features a large integral display that shows real-time process status in mA, percent, or any designated 5-character Engineering units (EGU). Superior Accuracy–The loop-powered PSD reads any 4-20mA signal and displays the information with phenomenal accuracy of ±0.012% of input scale. And because it requires less than 2.3 Volts, it won’t burden most loops. Simple and Versatile PC Setup Program– Using the PC software, the PSD can either be custom scaled to display in a percent or scaled directly into engineering units for indicating process measurements such as pressure, temperature, level, or ﬂ ow. Span, zero, input range, display range, and ﬁ ltering frequency can also be easily programmed. Our software will even capture the input range limits of the loop to provide you with the most accurate display available

Details

PVT, PWT, and PWV AC Power Transducers

Moore Industries’ AC Power Transducers continuously track the amount of power being consumed by an electric device or a system. Available models accept an AC input from a “load” device such as a motor, pump or heater. They provide a proportional milliamp output for determining equipment power use and operating efficiency. They can also be used to trip automatic power control equipment to initiate energy conservation measures. Moore Industries’ AC power transducers are available in 1, 1-1/2, 2, 2-1/2, and 3 element versions. They may be either self- or externally-powered.

Details

R-BOX Enclosure for Rail-Mount Instruments

The R-BOX accommodates transmitters, meters, indicators, analyzers, integrators, and many other rail-mounted instruments. The variety of available R-BOX sizes means that we have an R-BOX that will ﬁ t your process needs. Choose from standard internal widths of 3, 6, 9, and 12 inches. Designed to meet Type 4X and IP66 ratings, the R-BOX is resistant to ultraviolet rays and chemicals. Its high-impact structure protects instruments even in harsh ﬁ eld conditions.

Details

RM100 Route-Master Fieldbus System (Intrinsically-Safe Installations)

The ROUTE-MASTER™ RM100 Series is an intrinsically-safe fieldbus power supply system providing galvanically-isolated and fieldbusconditioned power for FOUNDATION Fieldbus or PROFIBUS PA segments. Fieldbus devices may be connected into these segments only through RMA100 or RMA100C Device Couplers, and any intrinsicallysafe segment may only contain intrinsically-safe devices, that are approved for the appropriate Zone/Division of use and the appropriate Gas hazard.

Details

RotoFlo Series – Plastic Rotameter / Water / Chemicals

Ideal for Plastic Piping Quick Visual Indication Low Cost Simple Installation No Guide Rods

Features:

Quick & Clear Visual Indication
True Union Design for Easy Installation / Removal
Flow Ranges / 0.02 - 880 GPM
Ideal for Plastic Piping Systems
Low Pressure Drop
PVC End Connections
Optional Limit Switches
Low Cost

Details

Rugged ECT DIN Signal Isolator/Converter Reduces Installation Footprint with Thin 15mm Housing

The UL Approved ECT-DIN 2-Wire Isolator is now available in a narrow 15mm aluminum housing. The thinner ECT-DIN 2-Wire Isolator with 15mm width retains the same General and Hazardous area approvals as the rest of the ECT family of isolators. It also has the same RFI/EMI protection and -40°C to 85°C operating temperature range. The ECT-DIN 2-Wire Isolator can be installed in hazardous locations and does not require installation in climate-controlled environments, making it perfect for more extreme locations. The rugged narrow 15mm ECT DIN 2-Wire isolator and converter with 4-20mA, 1-5V and 0-10V inputs and 4-20mA output, permits more isolators to fit in cabinets and field enclosures where installation space is limited, saving space and money.” The ECT DIN 15mm narrow size allows more isolators to fit in cabinets and field enclosures where installation space is a premium. This is ideal for utilizing existing field mounted cabinets. The solid metal housing stands up to the continuous, daily rigors of process control and factory automation applications. An optional externally-mounted flange provides a secure mount, which ensures secure installation in high vibration environments. The ECT is UL approved Class I, Division 2, Groups A, B, C & D T4. The rugged and reliable ECT family of isolators provides versatile choices to match the type of AC or DC power available at each location. ECT-DIN 2-wire Output-Loop powered models, ECT 2-wire Input-Loop powered models, or 4-wire (Line/Mains) Powered Isolators/Converters and Splitters are also available. The complete ECT family delivers reliable signal isolation and conversion solutions for the most demanding ambient and noisy installation conditions. Download Data Sheet

Details

SB Stainless Steel, Explosion-Proof Enclosure for Hockey-Puck Instruments

The versatile construction of the SB stainless steel enclosure makes it ideal for use with any manufacturer’s hockey-puck units. It protects all Moore Industries’ hockey-puck instruments.

Details

ScrewPlug Immersion Heater

CX Screwplug Immersion Heater is used primarily to heat water in tanks through natural convection currents. Typical heaters have standard 1" - 2 1/2" NPT tapered plugs. Other sizes or plugs are available on special order.

Details

Self-regulating Heating Cable

Self-regulating heating cables consist of two parallel bus wires embedded in a networked plastic heating element, doped with surrounding carbon particles. If the temperature increases during operation, the plastic expands due to molecular expansion and the distance between the carbon particles increases. Resistance increases and output drops. When it cools down, this process is reversed and output increases. This physical property provides several benefits, including the ability to overlap the self-regulating cable and installation without the requirement of a temperature cut-out device. Benefits:

Self-regulating with adaptable output
Various temperature range applications
High chemical resistance
No temperature regulation or limiting required
Easy to lay and to install
Can be cut to length off the roll

Details

SENTINEL SERIES TELEMETRY TANK LEVEL MONITORING

The Sentinel is a Cellular Tank or Sump Level Monitoring system that delivers reliable daily measurements that are both scheduled and event driven. Remote monitoring with the Sentinel is exceptionally flexible, eliminating the hassles of network infrastructures and Internet service. Instead, the Sentinel connects via a wireless signal to local cellular networks and transmits Alarms, Inventory, Battery Status and GSM Signal Strength, all of which are available through the Sentinel Cloud Based Website. The Sentinel online provides you with important data readily at your fingertips on your Computer, Tablet or Smart phone.

Features:

Battery Operated - No Programming - One Button Only
Remote Monitoring through Cellular Networks
Wireless Communication GSM or Digital Wireless Radio
Frequency Bands GSM 850 / 1900 MHz WLAN
E-mail Reporting - Alarms, Text E-mail
24/7 access to data through Cloud Based Sentinel 247TM Online
Battery powered up to 5 years (3 calls/day)
Low Monthly Cost
Powerful - Long Range Antenna (Perfect For Remote Locations)
Access Data Via PC, Laptop, Smartphone, Tablet
Secure Cloud Data (password protected)
No Hidden Costs
Standard Batteries
Can be Mounted Directly to Top of Tank - 2" NPT
Eliminate Costly Emergency Fills or Pump-Outs

Details

Series 100P NEMA 4 & 13 Pressure Switch

Series 100P (diaphragm sensor) for pneumatic and low impulse hydraulics up to 3000 psig system pressure Versatile Nega-Rate® Belleville disc spring pressure switch for a wide range of applications. Specifications • Electrical: Snap action electrical switch recognized by Underwriters’ Laboratories, Inc. and CSA International • Electrical Connection: 1/2 NPT female conduit connection with terminal block • Pressure Connection: o Wetted Material 1 1/4 NPT Female o Wetted Material 4, 5, 7 and 9 1/2 NPT Female • Temperature Range o Ambient: -40°F to +180°F (-40°C to +82°C) o Media: -40°F to +300°F (-40°C to +149°C) • Media temperature limits change with O-Ring selection • Adjustment: Concealed wrench flat adjustment with range scale • Shipping Weight: Approximately 3 pounds

Details

Series 117P Sanitary Pressure Switch

Series 117P Sanitary Pressure Switch This field adjustable, compact pressure switch is intended for low- to mid-range process applications. The Tri-Clamp® compatible, polished, process connection makes this switch ideal for food, beverage and other sanitary services. Set point stability and vibration resistance are a function of the Nega-Rate® Belleville disc spring. This unit features 316 stainless steel construction, an explosion-proof/hermetically sealed electrical assembly, 18" standard free leads and SPDT or DPDT electrical forms and a wetted material surface polish of 9 - 11 micro inch Ra (0.23 - 0.28 micron Ra).† Specifications • Electrical: Snap action electrical switch listed by Underwriters’ Laboratories, Inc., FM Approval and CSA International • Electrical Connection: 1/2 NPT male conduit connection with PVC insulated 18 AWG, 18" long leads • Pressure Connection: 1 1/2" sanitary fitting mates with Tri-Clamp® fitting† • Temperature Range o Ambient: -40°F to +180°F (-40°C to +82°C) o Media: -40°F to +250°F (-40°C to +121°C) • Adjustment: Internal, slotted adjustment with range scale • Shipping Weight: Approximately 2 pounds

Details

Series 200P NEMA 4 & 13 Pressure Switch

Series 200P NEMA 4 & 13 Pressure Switch/Internal Adjustment Versatile Nega-Rate® Belleville disc spring pressure switch for a wide range of applications. Series 200P (piston sensor) for hydraulic applications up to 10000 psig system pressure. Specifications • Electrical: Snap action electrical switch recognized by Underwriters’ Laboratories, Inc. and CSA International • Electrical Connection: 1/2 NPT female conduit connection with terminal block • Pressure Connection: Wetted Material 1 1/4 NPT Female • Temperature Range*: o Ambient: -40°F to +180°F (-40°C to +82°C) o Media: -40°F to +300°F (-40°C to +149°C) *Temperature limits change with O-Ring selection • Adjustment: Concealed wrench flat adjustment with range scale • Shipping Weight: Approximately 3 pounds

Details

SewerWatch

SewerWatch the First Mobile App for Wastewater Infrastructure

Details

SFY Functional Safety Frequency-to-DC Transmitter with Display

Functional Safety Frequency-to-DC Transmitter with Display

The SFY Functional Safety SIL 3 capable Frequency-to-DC Transmitter with Display is part of Moore Industries’ FS Functional Safety Series. It monitors frequency, period, high or low pulse width, and contact closure signals and converts the input signal to a proportional, input-to-output isolated 4-20mA output ready for direct interface with a Safety System, readout instrument, recorder, PLC, DCS, SCADA system. The 2-wire (loop-powered) SFY is ideal for use in your Safety Instrumented System (SIS) in a wide range of process and factory automation monitoring applications:

Applications:

Turbine Tachometer Generators
Turbine Flow Meters
Magnetic Pickups
Dry Contact Closures
Variable Frequency Drives
Rotating Equipment
Pulse and Frequency Output Transducers
Motor and Conveyor Speed

Features:

exida certified to IEC 61508:2010. Certified by exida to IEC 61508 for systematic integrity up to SIL 3 and for random integrity up to SIL 2. This means that an SFY is approved for single use in Safety Instrumented Systems (SIS) up to SIL 2 and in a redundant architecture (1oo2, 2oo3, etc.) up to SIL 3.
Comprehensive FMEDA certified safety data. Upon request, exida-certified FMEDA data is available for a functional safety practitioner to use in determining the SFY’s applicability in specific safety-related applications.
Exceptional accuracy and long-term stability. Typical accuracy is ±0.025% of span with up to 5 years between scheduled calibrations.
Sets up in minutes with PC software. You can choose, and then view to confirm, all application specific operating parameters.
Versatile input choices. Measures frequency ranges between an amazingly low 0.005Hz up to 25kHz; periods from 40microseconds to 200sec; and pulse widths from 0.2msec to 200 seconds.
Programmable moving average filter. Minimizes measurement instability caused by the effects of bent turbine blades and other frequency variations.
User-configurable display. A 5-digit LCD shows the process variable in selectable engineering units.
Input-to-output isolated and RFI/EMI protected. Resistant to unpredictable ground loops and the harmful effects of plant and equipment “noise”.

Details

Signal Conditioner

The K-system comprises signal conditioners for signal transfer between control system and safe area as well as isolated barriers for communication with field devices in hazardous areas. They are preferred for these kinds of mixed applications. Wide range of isolated barriers and signal conditioners for mixed applications Modules for universal power supply Reduced wiring by Power Rail Removable terminals Many modules with marine approvals and SIL assessment

Details

Signal Conditioner Compact Design

The SC-system is a signal conditioner product family for applications without hazardous areas on the field side. Modules for analog and digital signals Transmitter power supplies, isolated amplifiers, passive isolators, signal converters, and switch amplifiers 24 V DC supply Reduced wiring effort due to Power Bus

Details

Single & Multipath Spool Construction

VANTAGE 4800 Single & Multipath Spool Construction. The Engineering Team at Eastech believed that in order to absolutely meet all of the requirements of AWWA/ANSI C750–03, a flowmeter had to be designed that not only adhered to every section of the Standard, but also eliminated any possibility of improper installation, inaccurate velocity measurements, and less than adequate calibration procedures. A flowmeter, in order to meet these requirements, would have to possess the following features: Factory aligned spoolpiece sensors for guaranteed installed accuracy High accuracy flow measurement under disturbed flow profiles Advanced electronic meters with onboard dataloggers NIST traceable calibration under actual operating conditions

Details

SIY 2-wire PC-Programmable Signal Isolator and Converter

SIY PC-Programmable Signal Isolator/Converter combines smart digital technology with advanced analog operation to deliver superior reliability, accuracy, and ease of use. The highly versatile SIY programs to accept a wide range of current or voltage inputs. It outputs an isolated, proportional, 4-20mA signal. As a fl exible analog/digital hybrid, this 2-wire (loop-powered) transmitter programs in seconds to handle a wide range of important signal interface applications.

Details

SLD Functional Safety Programmable Loop Display

Moore Industries’ universal SLD PC-Programmable Functional Safety Loop Display features a large integral display that shows real-time process status in mA, percent, or any designated 5-character Engineering units (EGU). The SLD is part of Moore Industries’ FS Functional Safety Series products. It is certified by exida as a SIL3 capable, non-interfering device for use in a safety loop. The SLD Functional Safety Programmable Loop Display is the perfect solution to accurately and reliably display process status in a safety loop:

Features:

SIL3 Capability. The SLD is certifi ed by exida for non-interference in a safety loop. (It is not SIL3 assessed or certifi ed to be used as part of the safety function).
Easy-to-read, customizable display. The SLD’s independently confi gured display features two rows of large characters that can be clearly read in the fi eld and set to display any EGU.
360° fl exible mounting. When placed into one of our housings, the SLD can be mounted at any angle in nearly any environment.
Low voltage drop. Loop-powered by less than 2.3 Volts, the SLD can even be installed on burdened loops.
Loop Maintenance Zener Diode Option. Allows the SLD to be removed from the loop for maintenance without interrupting your safety function.
Custom and square root curves. Select a square root or linear curve from the library, or create your own. Use our software to input a table in one EGU and have the PC program convert it into a different EGU for display.

Details

SPA2 4-wire site and and PC-Programmable Current and Voltage; RTD and Thermocouple Limit Alarm Trips

The universal SPA2 Programmable Limit Alarm Trips provide on/off control, warn of unwanted process conditions, alarm on rate-of-change and provide emergency shutdown. Very versatile, they accept a signal input from transmitters, temperature sensors and a wide array of other monitoring and control instruments

Details

SPAIS Programmable Limit Alarm Trips with Intrinsically-Safe Field Connections

The universal SPA2IS Programmable Limit Alarm Trips provide on/off control, warn of unwanted process conditions, alarm on rate-of-change and provide emergency shutdown. Very versatile, they accept signal inputs from transmitters and temperature sensors that are located in hazardous areas where the method of protection implemented by the plant or facility is Intrinsic Safety.

Details