These 2-wire (loop-powered) I/P transmitters accept a current signal (such as 4-20mA) from a DCS, PLC or PC-based control system. They convert the current signal to a pneumatic signal (3-15psig, 0.2-1bar, 20-100kPa, etc.) to provide precise, proportional control of valves, actuators and other pneumaticallycontrolled devices. The economical IPH2 (Type 4X) is watertight, dust-protected, and resistant to corrosion and chemicals. In addition to meeting Type 3X/4X requirements, the IPX2 can be installed in explosionproof environments. Both units are available with an optional coalescing fi lter/regulator that combines an air fi lter and miniature supply line regulator with a pressure gauge that reads in both psig and bars. -
These 2-wire (loop-powered) I/P transmitters accept a current signal (such as 4-20mA) from a DCS, PLC or PC-based control system. They convert the current signal to a pneumatic signal (3-15psig, 0.2-1bar, 20-100kPa, etc.) to provide precise, proportional control of valves, actuators and other pneumaticallycontrolled devices. The economical IPH2 (Type 4X) is watertight, dust-protected, and resistant to corrosion and chemicals. In addition to meeting Type 3X/4X requirements, the IPX2 can be installed in explosionproof environments. Both units are available with an optional coalescing fi lter/regulator that combines an air fi lter and miniature supply line regulator with a pressure gauge that reads in both psig and bars. -
The high-performance IPT 2 Current-to-Pressure (I/P) Transmitter converts a current signal to a pneumatic signal so that an electronic-based system such as a DCS, PLC, or PC can control a pneumatic actuator, valve, or damper drive. Available models accept a wide range of current inputs (4-20mA, 4-12mA, and 12-20mA) and provide a proportional pneumatic signal (3-15psig, 0.2-1 Bar, 20-100kPA, etc.). -
These 2-wire (loop-powered) I/P transmitters accept a current signal (such as 4-20mA) from a DCS, PLC or PC-based control system. They convert the current signal to a pneumatic signal (3-15psig, 0.2-1bar, 20-100kPa, etc.) to provide precise, proportional control of valves, actuators and other pneumaticallycontrolled devices. The economical IPH2 (Type 4X) is watertight, dust-protected, and resistant to corrosion and chemicals. In addition to meeting Type 3X/4X requirements, the IPX2 can be installed in explosionproof environments. Both units are available with an optional coalescing fi lter/regulator that combines an air fi lter and miniature supply line regulator with a pressure gauge that reads in both psig and bars.
Download Data Sheet -
H-System connects to the control system via a system connector and cable, reducing planning and start-up time. Pre-wired boards and snap-on interface modules make maintenance simple. Combined with minimized space requirements and low power dissipation in the cabinets, the H-System is a cost-effective solution. -
ITC 650 SERIES – UNVERSAL MULTICHANNEL INDICATOR - 8 Inputs
The Levelpro ITC 650 Universal Data Logger can display current and record values from 8 different measuring channels. Each channel can be individually designated (described) with any engineering measuring unit. The LCD graphical display allows for visualization of the values from all 8 channels simultaneously. A significant advantage is possibility of viewing the trends in each measuring channel.
Applications:
- Temperature
- Flow
- Pressure
- PH
- Level
- Redox
- Humidity
- Current
Features:
- Universal Multi-Channel Indicator
- LCD Graphic Display Up to 8 inputs Universal / (4-20mA)
- 2 Electronic Relay Outputs
- 24VDC Power Supply Output: 24VDC / 200mA Will Power All 8 Channels
- RS-485 / Modbus RTU Standard
- Temperature / Flow / Humidity / Pressure / PH / Redox / Level / Current
- Viewing the Trends in each of the 8 Measuring Channels
- Any Text Description Possible: Name and Units
- Data transfer to the Master System via RS-485
- Password Protected
Specification:
- Power Supply: 120VAC -24VDC
- Inputs: 2 /4 /8 Inputs / 4 - 20mA
- Relay Outputs: 2 electronic relays / NO type (ER1, ER2 with max. load 24VAC / 35VDC / 200mA
- Communications: RS485, Modbus RTU
- Operating Temperature: -10°C to +70°C
-
ITC 7200 SERIES – UNVERSAL CONTROLLER- 48 Inputs
The ITC series advanced controllers and recorders have been designed for to handle and control advanced industrial applications.
Applications:
- Temperature
- Flow
- Pressure
- PH
- Level
- Redox
- Humidity
- Current
Features:
Trending DiagramsUniversal Data Logger / Controller / Display ITC 7200 Series 1.5 GB for data! The ITC series data loggers can record channels at a speed of 10 samples per second. It has 1.5 GB built-in flash memory intended for data registration. .DAQ ManagerTo manage large amounts of data we have designed a software package that is free of charge. The software converts the data into easy viewing graphs and tables, and can provide group measurement results, create reports and export data into other files. Its fully functional free version can be downloaded from our website or ordered as a payable CD-ROM version.Color LCD TouchscreenThe color touchscreen allows for easier and more efficient use of the device The display reacts accurately to even the slightest touch. The ITC also allows for the use of a traditional keyboard and a USB mouseUse Java appletsIt is possible to create your own website or use one of the templates included in ITC series. Applications such as tank level via with bar graphs, flow meters indicating flow speed or total liquid flow, a pressure gauge indicating process pressure...all are possible with the ITC series This solution makes monitoring of the entire system much more transparent and simple to use.Measure / Recalculate / Control and DisplayCalculate the data according to your own requirements; one result can be used as an argument of another action. An example, current measurement from 8 channels and voltage from 8 channels cross checked against the total power from 8 items being measured. All data can be visualized in a range of ways: as numerical values, quasi-analog indicators, phasor charts, horizontal or vertical charts, horizontal or vertical bars.Manage a Developed Network of DevicesFor more demanding customers with many needs we have prepared the Advanced Communication Module (ACM). This module includes interfaces such as: Ethernet, USB Host, RS-485 and RS-485 shared with RS-232. All the Modbus interfaces can work in both master and slave mode. Through the utilization of an Ethernet link the user can monitor operation of the entire system via the Internet from anywhere in world, via an INTERNET browser. In addition the data can be monitored via the RS-485 interface along with PC software.Specification:
- Power Supply: 19 to 50VDC , 16 to 35VAC , 85 to 260VAC/DC
- Inputs: Universal, Thermocouples: J,K,S,T,N,R,B,E(PNEN), L(GOST), RTD 2-3 wire, Pt100, Pt500,Pt1000, (PN_EN),GOST Ni100, Ni500, Ni1000(PN-En), Cu50,Cu100 (Pn-83M-53852), Universal pulse 5kHz
- Outputs: 4-20madc, SPST Rely 1A/250V
- Communications: RS485, Modbus RTU
- Operating Temperature: 0°C to 50°C
-
ITC 8000 SERIES - UNIVERSAL CONTROLLER - 72 Inputs
The ITC series advanced controllers and recorders have been designed for to handle and control advanced industrial applications.
Applications:
- Temperature
- Flow
- Pressure
- PH
- Level
- Redox
- Humidity
- Current
Features:
Trending DiagramsUniversal Data Logger / Controller / Display ITC 8000 Series 1.5 GB for data! The ITC series data loggers can record channels at a speed of 10 samples per second. It has 1.5 GB built-in flash memory intended for data registration. .DAQ ManagerTo manage large amounts of data we have designed a software package that is free of charge. The software converts the data into easy viewing graphs and tables, and can provide group measurement results, create reports and export data into other files. Its fully functional free version can be downloaded from our website or ordered as a payable CD-ROM version.Color LCD TouchscreenThe color touchscreen allows for easier and more efficient use of the device The display reacts accurately to even the slightest touch. The ITC also allows for the use of a traditional keyboard and a USB mouseUse Java appletsIt is possible to create your own website or use one of the templates included in ITC series. Applications such as tank level via with bar graphs, flow meters indicating flow speed or total liquid flow, a pressure gauge indicating process pressure...all are possible with the ITC series This solution makes monitoring of the entire system much more transparent and simple to use.Measure / Recalculate / Control and DisplayCalculate the data according to your own requirements; one result can be used as an argument of another action. An example, current measurement from 8 channels and voltage from 8 channels cross checked against the total power from 8 items being measured. All data can be visualized in a range of ways: as numerical values, quasi-analog indicators, phasor charts, horizontal or vertical charts, horizontal or vertical bars.Manage a Developed Network of DevicesFor more demanding customers with many needs we have prepared the Advanced Communication Module (ACM). This module includes interfaces such as: Ethernet, USB Host, RS-485 and RS-485 shared with RS-232. All the Modbus interfaces can work in both master and slave mode. Through the utilization of an Ethernet link the user can monitor operation of the entire system via the Internet from anywhere in world, via an INTERNET browser. In addition the data can be monitored via the RS-485 interface along with PC software.Specification:
- Power Supply: 19 to 50VDC , 16 to 35VAC , 85 to 260VAC/DC
- Inputs: Universal, Thermocouples: J,K,S,T,N,R,B,E(PNEN), L(GOST), RTD 2-3 wire, Pt100, Pt500,Pt1000, (PN_EN),GOST Ni100, Ni500, Ni1000(PN-En), Cu50,Cu100 (Pn-83M-53852), Universal pulse 5kHz
- Outputs: 4-20madc, SPST Rely 1A/250V
- Communications: RS485, Modbus RTU
- Operating Temperature: 0°C to 50°C
-
By combining low-cost wireless sensing with high-speed automated analytics, iTracking® Systems provide Cities, Utilities and Consulting Engineering firms with all the necessary tools for:
Inflow & Infiltration Micro Detection
Early-Warning Overflow and Backup Prevention
Dynamic Condition Assessment
Fact-Based Model Validation -
K-System isolated barriers offer an extensive range of intrinsic safety interface modules for many signals and applications – from simple isolators to highly functional modules. Furthermore, the signal conditioners are the perfect choice for general-purpose. Both types of modules can be mounted on the same Power Rail. They are clearly differentiated by color as signal conditioners have grey front labels. K-System modules are available in a variety of housing widths so they easily fit into any cabinet or enclosure. Whether one chooses the 12.5 mm KC-modules or the 20mm and 40mm KF-modules, the electrical and mechanical characteristics of the K-System are maintained. -
Kepware's KEPServerEX
Connects disparate devices and applications, from plant control systems to enterprise information systems
KEPServerEX is the industry’s leading connectivity platform that provides a single source of industrial automation data to all of your applications. The platform design allows users to connect, manage, monitor, and control diverse automation devices and software applications through one intuitive user interface. KEPServerEX leverages OPC (the automation industry’s standard for interoperability) and IT-centric communication protocols (such as SNMP, ODBC, and web services) to provide users with a single source for industrial data. The platform is developed and tested to meet our customers’ performance, reliability, and ease-of-use requirements.Business Value:
KEPServerEX provides the industrial connectivity, usability, and performance required by the enterprise—offering competitive benefits that can be experience from the plant floor to IT to the boardroom.
Features:
- Accessibility ... KEPServerEX provides access to client applications (like MES and SCADA) and IoT and Big Data analytics software via OPC, proprietary protocols (including GE NIO, SuiteLink/FastDDE, and Splunk), IT protocols (including MQTT, REST, ODBC, and SNMP), and flow measurement export to common Oil & Gas industry and customized formats.
- OPC
- Automation Interface
- IT Interface
- Cloud Interface
- Exporters
- Optimization ... KEPServerEX optimizes communications and reduces network and device load via data conditioning and reduction, customized load balancing, and protocol-specific communications optimization.
- Data Conditioning and Reduction
- Redundancy
- Load Balancing
- Communications
- Machine-to-Machine Linking
- Programmatic Changes
- Aggregation ... KEPServerEX simplifies the configuration of connected applications by providing a single point of entry to all information—eliminating the need to purchase, operate, troubleshoot, and maintain multiple disparate solutions for discrete connectivity.
- Centralized Platform
- Unified Configuration
- Data Storage and Retention
- Connectivity ... KEPServerEX supports the broadest range of drivers available, including current and legacy devices across various verticals, a variety of wired and wireless network mediums, and connectivity to databases, custom software applications, and other OPC servers.
- Driver-Based Access
- Telemetry Environments
- Rapid Deployment
- Simulation
- Security ... KEPServerEX includes a variety of tools that control user access to the server, data source, or data values, regulate read/write access, provide the ability to disconnect client applications, and support the configuration of secure data tunnels.
-
Configuration
-
Runtime
-
-
Diagnostics ... KEPServerEX isolates device and application communications for troubleshooting, offering OPC diagnostics for real-time and historical views of OPC events and communications diagnostics to capture the protocol frames transferred between the server and any device.
- OPC Diagnostics
- Communications Diagnostics
- Third-Party Diagnostics Integration
- Accessibility ... KEPServerEX provides access to client applications (like MES and SCADA) and IoT and Big Data analytics software via OPC, proprietary protocols (including GE NIO, SuiteLink/FastDDE, and Splunk), IT protocols (including MQTT, REST, ODBC, and SNMP), and flow measurement export to common Oil & Gas industry and customized formats.
-
Perfect for Head-Mount Instruments The LH connection heads are ideal for use with head-mount transmitters such as Moore Industries’ TRX/TRY PC-Programmable and THZ2 Smart HART® Temperature Transmitters. The LH heads also protect terminal blocks used for sensor wire terminations. -
Limit value switches signal whether the medium being monitored has reached, risen above, or fallen below, a set level (VDI/VDE Directive 3519) based on its installation height.
Examples:
Overflow / dry-run protection
Minimum-maximum control
Overspill protection -
Perfect for tank level measurement and control
The FLOMOTION LM7000 provides non-contacting level measurement for a wide variety of applications in both liquids and solids. The system is composed of an ultrasonic sensor and a remote mounted controller for maximum flexibility. Easy calibration and maintenance-free performance means you can install the LM7000 rapidly and with confidence. Features:- Measurement range 33 ft (S330 sensor) or 50 ft (S500 sensor)
- Programmable 4-20mA analog output
- Menu driven programming
- 4-20mA and relay outputs
- 3 or 6 SPDT relays for alarms and external control
- Sensor is weather resistant and safe against submersion (NEMA 6P)
- Automatic temperature compensation
- Datalogging
- Single or Dual Sensor
-
LP 200 SERIES Plastic Pressure Sensor / Transmitter
The Levelpro LP200 was designed to measure Pressure or Level within industry's most demanding corrosive process applications. When measuring pressure It can be mounted vertically or horizontally, and can easily be installed into a threaded process pipe tee fitting. For level measurement applications the LP200 can simply be mounted into the side of the tank utilizing a NPT / G type bulkhead or weld-o-let fitting. The LP200 implements a state of the art ceramic measuring principle that changes the physical pressure which equates to no more than a few microns into a linear electronic signal that can be measured. This minimal deformation equates to negligible material strain of the ceramic electronic pressure-sensing diaphragm resulting in high resistance to alternating loads and long-term durability...exactly what is required for tough industrial applications.
Typical Applications:
- Chemicals / Acids / Bases
- Tank Level
- Industrial Process Piping
- Vapor Pressure
- Leak Detection Equipment
- Environmental Protection
- Scrubbers Filter / Strainer Notification
- Leachate Collection
- Weir Flow
- Scrubbers
Features:
- PP / PVDF / 316 SST Body
- Pressure Range / 0 - 225 psi
- Output / 4-20mA / 2 Wire Loop Powered
- NPT / G / Union Type Connection
- Ceramic Sensing Diaphragm
- Plug & Play Design
- High Accuracy
- No Programming Required
- Temperature Compensated
- Excellent Chemical Resistance
Specifications:
- Range 0 - 225 psi / (Other Ranges Available)
- Medium Gas & Liquid
- Accuracy 0.2% or 0.5% F.S
- Working pressure 18 - 36V DC
- Output signal 4-20mA / two-wire
- Medium temp -30°C - 85°C
- Environment temp -30°C - 80°C
- Store temp -30°C - 80°C
- Temp. effect ±0.02% FS
- Pressure connection ¾" NPT / G Type / ½" Union Type
- Connection DIN Hirschminn Connector
-
LS Series PP Body Plastic Paddle Wheel Flow Transmitter
ZIRCONIUM CERAMIC SHAFT / BEARINGS ALL PLASTIC CONSTRUCTION RETROFITS into SIGNET® TYPE FITTINGS
Features:
- Industry’s Highest Accuracy-0.75%
- Excellent Chemical Resistance, PP/PVDF, PFA, Ceramic
- Sensor Body Material PVDF / PP
- Rotor Material PFA (Teflon)
- Shaft and Bearings Zirconium Ceramic (Zr02)
- O-ring Material FKM (Viton) / EPDM optional
- Size Range ½” - 24” • Measuring Flow Range (0.33 Ft/Sec To 26 Ft/Sec)
- Excellent For Low Or High Temperatures -20 To 90°C (-4 To 194°F)
- NEMA 4X (IP65) Or NEMA 6 (IP68) Rating
- Extra Long Lasting PFA Paddle Assembly (Zirconium Ceramic Shaft & Bearings-Standard)
- Double FPM O-Ring Seal
- High Pressure Rating (Up To 200 Psi)
- Frequency Output -18.5Hz /Ft/Sec
- NPN Pulse Output
- Supply Voltage 5 to 24Vdc
- Electrical Connection DI Mini-Connector 43650-A (IP65) , Electrical Cable (IP68)
- Cable Type 3 conductor + shield 26AWG (PVC)
- Reverse Voltage Protection Standard
- Output Frequency 60.5Hz m/s nominal ( 18.45HZ ft/s nominal)
- Measuring Viscosity Range 0.5 to 20 cts
- Maximum Particle Size <0.5mm2 (Max particle size)
- Maximum Operating Pressure 200psig at -30C
- Maximum Temperature 36 psi at 90C
Technical Information:
- Truflo Clamp Saddles can be used with PE, PP, PVDF PVC Pipe
- The Use of teflon tape is advised.
Materials:
- PPGF. - Polypro Glass Filled
- FPM O-ring
- 316 SSt
- Reinforced Outlet 316 SSt
-
LSS Series PP Body Plastic Paddle Wheel Flow Meter
Features:
- Up to 24" Pipe Size
- Zirconium Ceramic Rotor / Bearings
- Accuracy ±0.75% of Full Scale
- Retrofits Into Signet® Type Fittings
- Large Display Changes from Green to Red when in Alarm State
- Accuracy ± 0.75% Of Full Scale
- Pipe Size (1/2 -24 Inch)
- Heavy Duty Industrial Design
- Sensor Body Material Natural PVDF / PP
- Rotor Material PFA Teflon
- Shaft and Bearing Material Zirconium Ceramic (Zr02)
- Display Housing Material Polymide 66 +PBT + 15% Glass Filled (UL94V-0)
- Flow Rate + Totalizer (Resettable)
- Memory Mode Non-Volatile EPROM
- Flow Velocity Range (0.33 to 26 Ft/S) (0.1 To 8 M/S)
- Measuring Viscosity Range 0.5 to 20 cts
- Maximum Particle Size <0.5mm2 (Max particle size)
- Maximum Operating Pressure 200psig at -30C
- Maximum Temperature 36 psi at 90C
- Eprom Memory-Totalizer Value Will Not Be Lost
- Nema 4X (IP66) Protection • Bright LED Display Flow Units-- Litre, USGPM, M3, Ton
- 4-20mA + Two (7) Amp Relays Output (Standard)
- Output Frequency 60.5Hz m/s nominal ( 18.45HZ ft/s nominal)
- Pulse Output Transistor NPN Open-collector (Max. DC 60V/100ma)
- Supply Voltage 14 to 28Vdc
- Communication RS-485 Modbus RTU Mode
- Protection Class IP65/ NEMA 4X
- Corrosion Resistant All Plastic Wetted Parts-PVDF/PP Body Zirconium Ceramic Shaft-PFA Teflon Paddle
- Simple Installation
- Up to 24" Pipe Size
-
The LT260 Series is designed to measure liquid level in a wide variety of applications.
The compact, loop-powered LT260 provides continuous, non-contacting level measurement. With a measuring range of 26ft (8m) the LT260 will accommodate a wide range of applications.
The large LCD display, 4 status lights and 5 button keypad make setup and operation quick and easy.
Features:
- Low Cost
- High Accuracy
- Non-Contact Measurement
- No Moving Parts
- Compact, Lightweight Design
- Corrosion Resistant Materials
- Built-in Temperature Compensation
- Programmable 4-20mA Output
- Selectable Transducer Power Level
- Adjustable Damping
- Displays Level, Distance or Space
- Loss of Echo Indicator
- Interface this level sensor with the FLOMOTION DR5000 Chart Recorder
- Bulk Chemical Storage
- Pump Stations
- Clarifiers
- Filtration Levels
- River Level Monitoring
- Trash Rack Level Monitoring
- Waste Sump
- Tanker Truck Filling
- Water Storage Towers
- Reactors
-
The LT330 Series is designed to measure liquid level in a wide variety of applications.
The compact, loop-powered LT330 provides continuous, non-contacting level measurement. Up to 33ft (10m) range.
The large LCD display, 4 status lights and 5 button keypad make setup and operation quick and easy.
Features:
- 33ft (10m) range
- Accuracy of 0.2% with 1mm resolution
- Easy to install 2” NPT fitting
- Loop powered 4-20mA (max 750 Ω)
- 5 digit numeric LCD display
- Integral 5 button keypad
- 4 status lights
- Built-in temperature compensation sensor
- Bulk Chemical Storage
- Pump Stations
- Clarifiers
- Filtration Levels
- River Level Monitoring
- Trash Rack Level Monitoring
- Waste Sump
- Tanker Truck Filling
- Water Storage Towers
- Reactors
-
MLD-35 Series Teflon® Capacitance Level Sensor
MLD-35 Series Continuous Level Sensors are intended for level measurement of liquid and bulk solids in tanks, vessels sumps or silos, hoppers, etc. They are comprised of a housing with electronic module and a electrode that converts a capacitance signal to a current signal of 4-20mA or voltage signal (0-10V) output. The MLD series incorporates a Teflon® encapsulated measuring electrode making it suitable for corrosive chemicals and sticky polymers.Features:
- Continuous Level Measurement of Liquids or Bulk Solids up to 10 feet
- 4-20mA Loop Powered
- Supply Voltage 12-34 VDC
- Output Current 4-20mA (2-wire) / 0-10 VDC (3-wire)
- Teflon® Coated Electrode
- Excellent Chemical Resistance
- Visual indication of Function and Status of Level via two LED Lights located on housing
- Wide Selection of Electrical Connections
- Heavy Duty Design
- IP67 / IP68
- Temperature -40°C to 200°C
-
Teflon® Coated Guided Wave Radar
Continuous Liquid Level Meter
The MLR radar level meters are compact level measurement device that include a transmitter that emits microwave pulses along a rod or wire rope electrode. The pulse propagates along the electrode in the form of electromagnetic wave toward the level surface, where it is reflected and the signal wave component is returned to the receiving module of the electronic housing. The on-board circuitry measures the time of flight of electromagnetic wave and the distance to the surface level is calculated. According to the level height, the level meter output is set and the measured value is shown on the display. Radar level meters are resistant against changes in the atmosphere (pressure, temperature, dust, steam) and to changes in medium parameters (change in dielectric constant and conductivity).Features:
- Suited for Continuous Level Measurement of various Liquid / Bulk Solids / Viscous Materials
- View Measured Values on the Display
- Universal Use / Direct Mounting onto Hoppers / Silos / Tanks / Sumps
- Teflon® Coated Stainless Steel Rod or Rope
- Electrode Measuring Range up to 40m
- Explosion Proof / ATEX (Optional)
- Temperature -40C to 200C
- Pressure Steel Rod (30°C/4MPa , 85°C/2MPa , 130°C/2MPa, 160°C/1,5MPa200°C/0.3 MPa) Rope (30°C/1MPa, 85°C/0.5MPa,130°C/0.1MPa)
- Current Output (4-20mA) / HART® Protocol
- Supply voltage 18 to 36VDC
- IP67
-
The microNCS provides a real-time signal gateway between the field or factory floor and your control strategy. Part of Moore Industries’ NCS NET Concentrator System® family of intelligent distributed I/O, the stand-alone microNCS accepts four or eight fully-isolated analog inputs and four discrete (contact closure) inputs. It “concentrates” this data onto one or multiple communication links, and transmits it long distances back to one or more host DCS, PLC or PC-based control systems. -
The JP-450 is a magnetically actuated “no bleed” pneumatic point level switch for use with magnetic liquid level indicators. Magnetic coupling through the chamber wall keeps the switch isolated from process fluid and pressure, allowing setpoints to be adjusted on the fly. Two JP-450’s can be coupled with a JPLR latching relay to give plug-and-play dump/fill valve control.
Features:
- No process piping or valves required (except customer pneumatic lines)
- Retrofit onto existing MLG installations
- “Snap-action” design maintains state in high-vibration environments
- Accepts filtered air or gas supply
- Field configurable (High/Low level)
- 316 Stainless Steel enclosure
-
The JS-10 (1 amp) and JS-30 (3 amp) switches are magnetically actuated point level switches for use with magnetic liquid level indicators. Magnetic coupling through the chamber wall keeps these switches isolated from process fluid and pressure, allowing setpoints to be adjusted on the fly.
Features:
- No process piping or valves required
- Retrofit onto existing MLG installations
- Internal bias magnet maintains state in high-vibration environments
- Available in SPDT (one internal switch) or DPDT (two internal switches)
- Available with flying leads (no enclosure), Epoxy-coated Aluminum enclosure, or 316 Stainless Steel Enclosure
- Class I, Division 1, Groups B, C, D
- Class I, Division 2, Groups ABCD
- Class II and Class III, Groups EFG
- ATEX and IEC ratings (pending)
- Maintenance-free
-
Featuring a very narrow installation footprint,
miniMOORE™ Signal Isolators, Converters, Boosters
and Splitters combine multiple analog signal channels
in a rugged, easy-to-install signal conditioner.
Reliable and very economical, the miniMOORE
multi-channel family includes the model MIX 2-wire
(loop) and the model MIT 4-wire (line/mains) powered
models. The complete family delivers cost-effective
solutions for an expansive range of signal interface
applications. -
OMNI pioneered flow computing based on maintaining a fixed calculation cycle time rather than task loading. Today’s OMNI flow computer still maintains a measurement calculation cycle time of 500ms that exceeds any industry requirements.
Calculations are carried out in double precision (64-bit), floating point format for greatest accuracy. Totalization integrity is assured through the well established industry practice of
triplicated (Tri-reg) storage and checking routines.
OMNI Features:
With its fast one second power-up recovery, field proven reliability, longevity, and usability, OMNI has the lowest cost of ownership in the business. The result of continuous end user requirement development, the OMNI track record stands alone protecting the interest of both buyer and seller in Custody Transfer measurements.
- One second power up
- Three year Limited Warranty
- Crude Oil, Refined Products, LPGs, Anhydrous Ammonia, Ethylene, Chemical, Natural Gas, NGLs, Specialty Gases, Water and Steam Product selection
- Stream, Batch and Station totalization
- Multiple Products with individual product totalizers
- Multiple Batch Consolidation
- Batch recalculation
- Batch Stack – Product Scheduling
- Automatic prove sequence control
- All Meter Types: DP, PD, Turbine, Coriolis, Ultrasonic
- K-Factor and Meter-Factor Linearization
- Viscosity Linearization
- All Prover types
- Multiple I/O types, 4-20mA, 1-5V, HART, Honeywell DE, Rosemount MV, Coriolis MVS
- Meter run and Station densitometer
- Redundant Gas Chromatograph interface
- Run Switching
- Premium Billing
- Maintenance Mode
- Multiple Modbus/TCP and Modbus over Ethernet (Multiple socket) as well as conventional RS232/485 connections
- AC or DC powered
- Configure from Keypad or PC
- Multiple Metrological Approvals
- Broad ambient temperature range
- Calculations performed to 64 bit double precision accuracy
- PID control loop with Primary and secondary control parameters
- Virtual inputs for system simulation and testing
- Unique on-board Help
- Simple firmware upgrades
-
VANTAGE 4700
Multipath Flowmeters. Two and three path diametrical sensor configurations are recommended for applications that do not have normal upstream straight runs to produce well developed velocity profiles -
MV800 Ultra compact electromagnetic flow meter converter suitable for connection to full-bore ISOMAG® sensors up to 16
Features:- Ultra compact converter suitable for connection to ISOMAG ® MS1000 or MS2500 sensors up to 16 inches
- Suitable for flow measurement of liquids with a minimum conductivity of 20 µS/cm
- Measuring accuracy +/- 0.5% of reading
- Cast aluminum or 304 SS housing
- Nema 6 (IP 67) protection rating
- Power supply 10 - 30 VDC @1W, electrical connections via 5-pin connector
- Up to two digital pulse outputs and/or 4-20mA outputs available
- PC programming via USB cable and dedicated software (MCP Protocol)
- No moving parts
- Bi-directional flow measurement
- Every sensor is factory wet calibrated and tested
-
Fluidwell launches the new N413 Batch Controller with receipt printing functionality. This is very useful for situations where you need a locally printed ticket as evidence of the delivered quantity like tank and truck (un) loading applications.
End-of-batch tickets and reprints can easily be printed automatically or on demand. Even in the unexpected event of an uncompleted batch, it is possible to print a ticket.
The N413 is a versatile and powerful batch controller, with a printer output, 2 field replaceable, heavy duty relays and three configurable transistor outputs. Relay 1 is fixed as main batch control output. Relay 2 and the transistor outputs can be configured as pump control with time delays, 2-stage batch control, alarm or pulse outputs. This makes the N413 a powerful and versatile batch or delivery controller.
The combination of the user-friendly numerical keypad with the compact, clear display, make the N-Series very attractive to our customers. The crystal clear LCD display, provides multiple batch control data simultaneously at a glance, including a graphical indication of the vessel, the batch process and the relay status. The bright backlight is standard available, ensuring perfect readings in all lighting conditions. -
The batch controllers of the N-Series are much more advanced compared to our F-Series and D-Series batch controllers. The N-Series distinguishes itself from other batch controllers by its very easy to use numerical keypad. Selecting and entering multiple preset values with the easy to press keys is astonishingly simple. The display is designed for batch processes: at a glance, the operator is aware of the indicated switch points and the actual state of the process. For your convenience the preset and the actual value with their engineering units are displayed simultaneously.
-
- All Plastic Design
- Excellent Chemical Resistant
- No Pressure Drop
Featues:
- Senses Liquid through Tubing
- Tubing Size ¼" to ½"
- Flow / No Flow
- Non-Intrusive
- Air Bubble Detection
- All Plastic Design
- Simple to Install
- Heavy Walled Tubing / Up to 0.062"
- Lightweight
- Very Accurate / Sensitivity Adjustment
- Perfect for Dosing or Metering Pumps
Specifications:
Applicable Pipes Size 3/8 - ½" / (7 to 13 mm) Materials PolyCarbonat Wall thickness 0.62" Sensing Object Liquid Sensing methods Electrostatic Capacitive / Photoelectric Repeat Accuracy ±0.2 mm max. Power Supply 12 to 24VDC /10% max. ripple / (10.8 to 30VDC) Current Consumption 12mA max. Relay Output Load current /NPN / PNP (100mA max) Residual voltage 1V max. (Load current: 100mA Indicators Detection indicator (orange) Ambient Temperature Range Operating: 0 to 55°C (with no icing or condensation), Storage: -10 to 65°C (with no icing or condensation) Ambient Humidity Range Operating/Storage: 25% to 85% (with no condensation)Ambient Humidity Range Operating/Storage: 25% to 85% (with no condensation) Temperature Influence ±4 mm of detection level at 23°C in the temperature Range of 0 to 55°C (with pure water or 20% saline solution) Voltage Influence ±0.5 mm of detection level at the rated voltage in rated voltage ±10% range Insulation Resistance 50 M Ohm min. (at 500VDC) between current-carrying parts and case Dielectric Strength 500VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration Resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock Resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions Degree of Protection IP66 (IEC) Connection Method Pre-wired Models (Standard cable length: 2 m) Weight (packed state) Approx. 70 g -
The NC30 Non-Contact liquid Level / Flow Sensor has been designed using high frequency technology to sense the presence of liquid / conductive / non conductive Suitable for Non-Metalic Tubing / Tanks / Drums / Pipe- Non-Contact
- Senses through wall
- Relay Output
- Conductive and Non-Conductive Liquids
Featues:
- All Plastic PP Design
- Non-Intrusive Liquid Level / Flow Detection through Plastic or Fiberglass Walls
- Small Footprint / Easy to Install
- LED Display
- M12 Disconnect or Fixed Cable Connector
- Fits on ½"- 2" Diameter Pipe / Sch 40 / 80
- Senses up to 0.3" / (8mm) Wall Thickness
Specifications:
Supply voltage 6 -30VDC Supply current Output type / Pulse Max. 0.6 / 7mA (OFF / ON State) Output type / S - Relay Max. 0.6mA (OFF State) Switched current (Min / Max) Output type / Pulse 100mA Conductive liquids 0.3" (8mm) Non-conductive liquids 0.11" / (3 mm) Ambient temperature range -20 / +80°C Temperature tube/vessel surface -20 / +90°C Housing material Plastic (PP) Protection class NEMA 4X / IP67 Cable Connection PVC Weight (including 2 m cable) Approx. 60 g -
Designed specifically for demanding industrial applications, the NET Concentrator System® (NCS) provides a real-time signal gateway between the field or factory floor and your control strategy. -
The SK-PC-Z1D1-UU1-10-HS USB intrinsic safety barrier enables a host device (i.e., an industrial PC) that is in a Zone 2 environment to be connected to an EXTA2/EXTA3 keyboard or similar USB device in a Zone 1/21 environment.The barrier enables operation of input devices, such as PC keyboards and trackballs, within Zone 1/21 and 2/22 hazardous areas. To transmit USB signals from and into hazardous areas, it converts the two USB channels into intrinsically safe circuits.The device is IP20 rated. It must be protected accordingly from adverse conditions, such as water spray or dirt, that exceed the conditions of pollution degree 2.As an associated apparatus, the SK-PC-Z1D1-UU1-10-HS barrier is certified to lead intrinsically safe circuits into Zone 1/21 hazardous areas. It is a one-to-one data connector. Data is passed through without buffering. The SK-PC-Z1D1-UU1-10-HS barrier does not provide galvanic insulation. -
All Plastic Design No Filling Required Excellent Chemical Resistance Pressure Range Markers
Features:
- All Plastic / Gauge & Isolator / Filled
- Heavy Duty Design / Simple to Install
- Completely Corrosion Resistant
- Designed to Act as Visual Pressure Alert for Bag / Filter Change-Out
- Extra Large Color Display
- Reduces Pressure Surges caused by Water Hammer / Metering Pump Pulsations
- Highest Accuracy in Industry / ±1.5%
- No Filling Required
- Glycerin Fill or Silicone (Opt)
- One-Piece Molded Design (No Assembly)
- Suitable for Corrosive Media + Slurries
Specifications:
Dial Diameter Large 2½" Face / Big Numbers / Clear Markers Mounting Direct Mount / Bottom Connection / ½" Housing PVC / CPVC / PP / PVDF / PTFE Teflon® Diaphragm / One Piece Molded Design Lens High Impact Polycarbonate Dial Red & Black Scale White Background, dial arc 270° Measuring Principle Bourdon Tube Diaphragm / Teflon® Movement SS316 / Brass / (Non Wetted) Gauge Red / Yellow / Green / Movable Plastic Pressure Pressure Markers Connection ½" (M) / (F) NPT / G Type / Flange Filling Glycerin or Silicone (Opt) Accuracy ±1.5% F.S. Operating Temperature PVC - 140°F / CPVC - 180°F / PP - 175°F PVDF - 225°F Pressure Range Standard Ranges / 0-60 / 0-100 / 0-160 psi (Second Scale: kPA) Other units available / bar / MPa / Other Scales (Non-Shock)
-
One Piece / Double-Sided Design No Filling or Assembly Required Adjustable Range Markers
Features:
- Industry's First All Plastic Double Sided Gauge
- Heavy Duty Rugged Design
- Completely Corrosion Resistant
- Designed to Act as Visual Pressure Alert
- Extra Large Color Display
- Reduces Pressure Surges caused by Water Hammer / Metering Pump Pulsations
- Highest Accuracy in Industry / ±1.5%
- Factory Filled / Glycerin or Silicone (Opt)
- Dual Scale / psi/kPA / psi/bar (Opt)
- One-Piece Molded Design
- Suitable for Corrosive Media + Slurries
Specifications:
Power Supply 24VDC Output SPST(Std) or PNP/NPN (Opt) Medium Density > 0.6g/cm3 Operation Point Vertically inserted approx 1" (25mm) Oscillation Starting Time About 3mm Response Time About 1 seconds Output DC 30V /3A Hysteresis settings About 3mm Relay Delay Time 1~505 Power Consumption < 1W Process Connection ¾" NPT/G Thread Electrical Connector M20x 1.5 (Electriccoated cable: 6-8mm) Material to Contact Liquid 316 SS Coated PTFE Teflon® Electrical Connection Gland M16 x 1.5 (standard)
-
Corrosion Resistant No Filling Required High Accuracy
Features:
- All Plastic Gauge & Isolator / Filled
- Heavy Duty Design / Simple to Install
- Completely Corrosion Resistant
- Range Markers Act as Visual Pressure Alert
- Extra Large Color Display
- Reduces Pressure Surges caused by Water Hammer / Metering Pump Pulsations
- Highest Accuracy in Industry / ±1.5%
- Glycerin or Silicone (Opt)
- No Filling Required
- One-Piece Molded Design / No Assembly
- Suitable for Corrosive Media / Slurries
Specifications:
Dial Diameter Large 2½" Face / Big Numbers / Clear Markers Mounting Direct Mount / Panel Mount Housing PP / Teflon® Diaphragm - One Piece Molded Design / (No Assembly / Filling Required) Lens High Impact Polycarbonate Dial Red & Black Scale White Background / dial arc 270° Measuring Principle Bourdon Tube / SS316 Diaphragm / PTFE Teflon® Movement SS316 / Brass Gauge Red / Yellow / Green / Movable Plastic Pressure Range Pointers Fitted on the Bezel Connection ½" (M) / (F) NPT / G Type / Flange Filling Glycerin / Silicone (Optional) Accuracy ±1.5% F.S. Operating temperature PVC - 140°F / CPVC - 180°F / PP - 170°F PVDF - 195°F Pressure Range* Standard Ranges / 0-60 / 0-100 / 0-160 psi (Second Scale: kPA) Other units available / (Non-Shock