-
HES HART to Ethernet Gateway System converts signals from wired HART devices to Ethernet MODBUS/TCP and HART-IP
Timely knowledge about your process enables better decisions and faster preventive action. Now you can get the process detail that you need from your Smart HART devices to MODBUS/TCP and HART-IP based monitoring and control systems at the speed of Ethernet with the HES HART to Ethernet Gateway System. Connect up to 64 Smart HART devices to the HES and collect the Dynamic Variables and the Device Variables, along with diagnostic bits and bytes, from each device that helps deliver critical information needed to help you address process and device problems before they turn into unplanned downtime. Moore Industries’ rugged HES supports HART 5, 6 and 7 devices with sufficient memory to handle thousands of process variables, and diagnostic data points from up to 64 connected smart HART devices. The HES allows you to further leverage your industrial Ethernet investment by making all of this valuable HART data viewable with any web browser or MODBUS/TCP compliant host. Support for these open industrial protocols enables you to easily interface with any process control or asset management system while taking advantage of any Industrial Internet of Things (IIoT) initiatives that facilitate the propagation of process data to higher level corporate or analytical systems. -
The HIM HART Loop Interface and Monitor unlocks the full potential of new and in-place smart HART multivariable transmitters and valves. Converts HART to 4-20mA Signals The HIM allows up to three additional analog process variable measurements from a smart device with no additional process penetrations or wiring. Download Data Sheet
-
HIT/HIX HART® Isolators provide highly economical solutions to common and costly problems that plague many of today’s “smart” process loops. Protect and enhance your HART investment with the 2-wire (loop powered) HIX or the 4-wire (line-mains powered) HIT. Download Data Sheet
-
From simple signal conditioning, to sensor-level I/O, to complex distributed intelligence, the versatile I/O EQUATION STATION ® is your solution. Even though it’s the same size as a typical process instrument, this multifunction I/O module configures to handle both routine, and one-of-a-kind, applications:
-
The rugged IPF Field-Mounted Current-to-Pressure Transmitter is designed specifically for installation in harsh environments. The two-wire IPF accepts a 4-20mA or 10-50mA input. It converts the input to a 3-15psig, 0.2-1bar, 15-3psig or 1-0.2bar pneumatic output signal, or to a wide variety of other commonly used pneumatic outputs (see Specifications for details). This versatility allows the IPF to interface with just about any kind of process control instrumentation including chart recorders, data loggers, panel meters, multiplexers, controllers and computers. The IPF can either be surface-mounted or mounted directly on a two-inch (vertical or horizontal) pipe. Two different types of housings are offered. The standard WP housing provides 1/2-inch NPT female wire entry threads while the metric WPM housing provides M20X1.5 female wire entry threads. The IPF transmitter is also available with an optional coalescing filter/regulator that combines both an air filter and a miniature supply line regulator. For more information on
-
These 2-wire (loop-powered) I/P transmitters accept a current signal (such as 4-20mA) from a DCS, PLC or PC-based control system. They convert the current signal to a pneumatic signal (3-15psig, 0.2-1bar, 20-100kPa, etc.) to provide precise, proportional control of valves, actuators and other pneumaticallycontrolled devices. The economical IPH2 (Type 4X) is watertight, dust-protected, and resistant to corrosion and chemicals. In addition to meeting Type 3X/4X requirements, the IPX2 can be installed in explosionproof environments. Both units are available with an optional coalescing fi lter/regulator that combines an air fi lter and miniature supply line regulator with a pressure gauge that reads in both psig and bars.
-
The high-performance IPT 2 Current-to-Pressure (I/P) Transmitter converts a current signal to a pneumatic signal so that an electronic-based system such as a DCS, PLC, or PC can control a pneumatic actuator, valve, or damper drive. Available models accept a wide range of current inputs (4-20mA, 4-12mA, and 12-20mA) and provide a proportional pneumatic signal (3-15psig, 0.2-1 Bar, 20-100kPA, etc.).
-
These 2-wire (loop-powered) I/P transmitters accept a current signal (such as 4-20mA) from a DCS, PLC or PC-based control system. They convert the current signal to a pneumatic signal (3-15psig, 0.2-1bar, 20-100kPa, etc.) to provide precise, proportional control of valves, actuators and other pneumaticallycontrolled devices. The economical IPH2 (Type 4X) is watertight, dust-protected, and resistant to corrosion and chemicals. In addition to meeting Type 3X/4X requirements, the IPX2 can be installed in explosionproof environments. Both units are available with an optional coalescing fi lter/regulator that combines an air fi lter and miniature supply line regulator with a pressure gauge that reads in both psig and bars. Download Data Sheet